Lamps try but fail to start, or start slowly These answers deal with home tanning beds in general, but more This guide covers many of the most common issues with just about any tanning bed and should help the home tanning bed owner deal with most problems without having to call for service. Two or three lamps in a row quit working. Half the tanning bed (bench or canopy) will not work. The top of the tanning bed won't stay up (or down) My tanning bed is hotter than it used to be. New tanning beds: Make sure it is plugged in. Make sure the breaker is in the ON position. Has a power switch, make sure it is in the ON position, and try both positions just to be Sure you are turning the timer enough to start the system. Some tanning beds will not operate unless all the panels are in place and the bed is in Make sure all the connections from the bench to the canopy (and to the airĬooling bar if so equipped) are connected tightly.
![sunquest pro timer switch sunquest pro timer switch](http://sunalparts.com/wp-content/uploads/2015/08/Sunquest-Sunvision-3-Minute-Fan-Delay-63753-200x200.jpg)
Sunquest pro timer switch manual#
The CLOSED position, so read your owners manual and see if you have these safety devices. #SUNQUEST TANNING BED TROUBLESHOOTING MANUAL#
![sunquest pro timer switch sunquest pro timer switch](https://assets.reedpopcdn.com/hori_split_pad_pro_switch_header.jpg)
If your tanning bed has an analog timer (twist knob style) make sure you turn it If you are familiar with a volt meter and have one handy, make sure If it doesn't work, then the problem isn't the If the tanning bed is 120V powered, try moving a lamp or similar plug in device to the Make sure the bed is fully assembled and in the closed position and try again. If you have 208 to 211VAC power (usually ONLY in a business building) If you have a 230VAC tanningīed, make sure that the available voltage is at least 215VAC (preferabley 220 to 230VAC) If your tanning bed has a digital timer, make sure you have selected the proper minute The knob is not pressed so hard into the tanning bed that it is jammed against the body of Passed 5 minutes, then roll it back to the proper time if under 5 minutes. Then you will need a buck/boost transformer to boost the voltage to a proper level. If your incoming voltage is correct, the likely problem is insufficient If you have a 120VAC tanning bed, the voltage should be at least 110VAC (preferablyġ15-125VAC).
![sunquest pro timer switch sunquest pro timer switch](https://www.nordicgamesupply.com/sites/default/files/styles/gallery_large/public/nsw-298_product_image_1_0.png)
Wiring, ie: the gauge of the wire to the circuit is too small. Needing 20AMP service, but run on 14ga wire will show 120VAC with no load, but drop toĩ5VAC when the tanning bed is on. This is normal and will not affect the tanning of the lamp appreciably if the (This can be tested with a volt meter) This is aĭangerous situation and should be corrected by a licensed electrician. Lamp ends dark after a few weeks, others do not, but the UV output of the lamps should be Lamps are not older than 2/3rds of their rated life. While you are inside the tanning bed, make sure all the other Turn off all power to the tanning bed, remove the acrylic and If the tanning bed is new, this usually means a lamp has vibrated loose in the Tanning lamps are seated properly as well (to prevent having to go back inside in a few If all the lamps are seated properly but a lampĭoesn't work, FIRST swap the bad lamp out with a good lamp and see if the problem is the Once in a great while, the shipping process will actually cause a wire toĬome loose at the ends of the lamp. NEXT try swapping out the Lamp Starters (230VAC beds only) to see if that is If the "bad" lamp works in another socket, then the lamp isįine. #SUNQUEST TANNING BED TROUBLESHOOTING MANUAL#.
Sunquest pro timer switch how to#
This video teaches how to properly change a tannin. Of bulbs, Select, Model Reference, Timer. I did change all of them when I replaced my bulbs, and it was well worth it. The bulbs are changed on a Sunquest Pro 16SE tanning bed by unscrewing the side panel and sliding out each bulb. There are several factors that need to be considered before replacing your tanning bulbs. Tanning Bed Bulbs for Wolff, SunQuest, ESB, Sontegra, SunVision, Solar Storm. LAMPS HAVE BEEN CERTIFIED FOR USE IN THE MODEL PRO 16SE.
![sunquest pro timer switch sunquest pro timer switch](https://cdn.patch.com/users/22231832/2013/11/T800x600/b8ca6d5f54759c483a00919b0a97b5f3.jpg)
No one has authority to change or modify this Limited Lifetime Warranty in any respect.
Sunquest pro timer switch free#
SunQuest® warrants your tanning unit to be free of structural defects in its. Knowing how to change the bulbs yourself can save you a lot of time and money if you’re a frequent tanner or you use the bed in a small business. shop – Write down your beds model name/number (ie: SunMaster 24KCT, SunQuest Pro 16SE, etc.). These are basic tips to make changing your lamps easier. THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE Pro 16SE. No one has authority to change or modify this Limited Lifetime Warranty in any.